GC type boiler feed pump technical parameters

Product Overview: GC boiler feed water pump single suction multistage centrifugal pump for conveying water and physical and chemical properties similar to liquid water. When the pump head of this type is 46m ~ 576m , the flow rate is 6m ~ 55m3 / h, and the liquid zui high temperature is lower than 110 °C . Suitable for boiler feed water , factory and city water supply. Pump with Y -type motor ­

­

Uses: Suitable for boiler feed water, mine drainage, factory and city water supply ­

Structural features: GC type water pump is horizontal, single suction multi-stage, segmented centrifugal pump ­

Medium temperature: ≤105°C

Treatment medium: clear water and liquid with physical and chemical properties similar to water ­

Drive mode: motor drive ­

Flow range: 6mз/h -55mз/h

Head range: 46m-430m

1.5 - the diameter of the suction port (mm) is divided by 25 and the whole ­

G ——Boiler feed pump ­

C —— indicates the type of pump ­

J - mechanical seal ­

5 - Reduce the number of revolutions to 1/10 pump. That is, the pump has a specific number of revolutions of 50.

6 - the number of impellers ­

1 , bushing nut 1 , Sleeve nut 2 , bearing cap 2 , Bearing Cover 3 , bearing 3 , Bearing 4 , bearing body 4 , Bearing body 5 , bushing 5 , Sleeve 6 , packing gland 6 , packing gland 7 , machinery Seal 7 , Sealing machine 8 , Inlet section 8 , Suction casing 9 , Sealing ring 9 , Wearing ring 10 , Impeller 10 , Impeller 11 , Mid-section 11 , Midsegment

12 , return pipe 12 , Balance pipe 13 , effluent section 13 , Discharge casing 14 , balance ring 14 , Balancing ring 15 , balance plate 15 , Balancing disk 16 , tail cover 16 , End cover 17 , bushing 17 , Sleeve 18 , pull Tightening bolt 18 , Tightening 19 , shaft 19 , Pump shaft 20 , round nut 20 , Round nut structure description ­

The inlet and outlet directions of the pump are all vertically upwards, and different stages are selected according to the required head. ­

The stator part of the pump consists of the inlet section, the middle section, the outlet section, the tail cap and the bearing body. ­

The rotor part of the pump consists of parts such as shaft, impeller, bushing and balance disc, and the two ends are supported on the ball bearings. ­

The static joint surface of the inlet, middle and outlet sections of the pump is sealed by tightening the bolts with a paper pad. In order to prevent water from entering the bearing, a "○" -shaped seal ring is installed between the sleeves. The shaft seals at both ends of the pump body are mechanically sealed. ­

The bearing body at both ends of the pump has an annular cooling chamber. When the liquid to be transported is greater than 80 °C , cold water should be introduced to cool the bearing. ­

The calcium-based butter grease in the bearing can be injected through the oil cup. ­

Seen from the direction of the inlet section, the pump rotates clockwise. ­

The yellow mealworm is not only rich in protein, fat, polysaccharid and other organic macromolecular nutrients, but also rich in phosphorus, potassium, iron, sodium, aluminum and other trace elements. For every 100g of the yellow mealworm larvae, the protein content of dry powder is between 48% and 54%, the fat content is between 28% and 41%, and the contents of vitamin E, B1 and B2 are also high. Therefore, the yellow mealworm can provide high quality protein for the black fish, and make the black fish big, strong and delicious.

Black Fish Feed

Black Fish Feed,5Kg Black Fish Feed,10Kg Black Fish Feed,15Kg Black Fish Feed

Fenxi Kangruilai Biotechnology Co., Ltd. , https://www.kangruilai-petfeed.com